Scan QR code
Attention to Lioncel
Return
Broadband amplifiers with low noise and low power consumption are used to improve the sensitivity of field strength testing and general attenuation testing, up to 18GHz.
Due to the built-in rechargeable battery, it can run without power supply within about 8 hours.
The input and output ports of the broadband amplifier are sensitive to electrostatic discharge. Therefore, precautions must be taken before touching the amplifier. (Coaxial cable and human body discharge).
The amplifier input has an SMA female connector. Provide a 0.5 meter long coaxial microwave cable to connect the antenna to the amplifier. The cable is equipped with SMA and N male connectors.
Usually the amplifier should be installed very close to the antenna. The amplifier housing is equipped with rubber pads for placing on a horizontal surface. In addition, there is a 22 mm hole in the housing to accommodate the mounting tube of the Schwarzbeck antenna. The antenna installation tube is usually placed horizontally, and the N female end output of the amplifier faces the ground. This avoids undesirable bending of the coaxial cable.
A typical installation example, with the AA9202 log periodic antenna ESLP 9145 and antenna mast AM9144 together.
main feature:
Broadband amplifiers with low noise and low power consumption are used to improve the sensitivity of field strength testing and general attenuation testing, up to 18GHz.
Due to the built-in rechargeable battery, it can run without power supply within about 8 hours.
The input and output ports of the broadband amplifier are sensitive to electrostatic discharge. Therefore, precautions must be taken before touching the amplifier. (Coaxial cable and human body discharge).
The amplifier input has an SMA female connector. Provide a 0.5 meter long coaxial microwave cable to connect the antenna to the amplifier. The cable is equipped with SMA and N male connectors.
Usually the amplifier should be installed very close to the antenna. The amplifier housing is equipped with rubber pads for placing on a horizontal surface. In addition, there is a 22 mm hole in the housing to accommodate the mounting tube of the Schwarzbeck antenna. The antenna installation tube is usually placed horizontally, and the N female end output of the amplifier faces the ground. This avoids undesirable bending of the coaxial cable.
A typical installation example, with the AA9202 log periodic antenna ESLP 9145 and antenna mast AM9144 together.
|
Nominal frequency range |
1 GHz-18 GHz |
|
Usable frequency range |
0.5 GHz-20 GHz |
|
Noise value |
2 dB |
|
Typical gain |
typ. 33 dB +/-5 dB |
|
Maximum input power |
- . 1 0 dBm ( . 9 7dBμV) |
|
1dB compression point (output a ) |
>+17 dBm (124 dBµV) |
|
Connector |
50 ohm, SMA |
|
Typical standing wave ratio (input/output) |
<2:1 |
|
powered by |
3.7V, 3.1Ah lithium ion |
|
Installation tube |
22mm diameter |
|
Typical working hours |
8h |
|
size |
155 x 80 x 67 mm |
|
weight |
About 1.0kg |
Shanghai Lioncel Electromagnetic Technology Co., Ltd(headquarters)）
Tel：021-66309055
Fax：021-56775110
Email：sales@emclioncel.com
Address：2-3F, Building 5, Lane 1175, Tongpu Road, Putuo District, Shanghai
Shenzhen Office
Tel：0755-25876847 18688776364
Fax：0755-25876847
Address：Floor 2, modern port office center, building a, film building, Guiyuan Road, Luohu District, Shenzhen
Beijing Office
Tel：17717042253
Address：Room 2003-1, Tower A, Shouke Building, 20th Floor, Building 1, Yard 14, Xisanhuan South Road, Fengtai District, Beijing
